IPCC cement production based on clinker

[edit / update model]
The category business/processes/production/cement/ipcc/clinker provides a methodology for calculating the emissions associated with cement production. The methodology is based on the quantity of clinker produced and represents the Tier 2 approach described by the IPCC Guidelines for National Greenhouse Gas Inventories (NGGIP). This methodology should be used where no information on the consumption of raw carbonate materials are available, but data on clinker production is available.

The IPCC Tier 2 methodology represented herein calculates emissions based on the quantity and properties of the clinker produced, as well as an estimate of the emissions associated with the production of cement kiln dust.

This approach is based on the following assumptions about the cement industry and clinker production:

  1. The majority of hydraulic cement is either portland cement or a similar cement, which requires portland cement clinker
  2. There is a very limited range in the CaO composition of clinker and the MgO content is kept very low
  3. Plants are generally able to control the CaO content of the raw material inputs and of the clinker within close tolerances
  4. Even where the output of clinker is calculated by a plant rather than directly measured, there is generally close agreement between the two determination methods when audits are performed
  5. The CaO content of clinker from a given plant tends not to change significantly over the years
  6. The main source of the CaO for most plants is CaCO3 and, at least at the plant level, any major non-carbonate sources of CaO are readily quantified (see Section 2.2.1.2 below)
  7. A 100 percent (or very close to it) calcination factor is achieved for the carbonate inputs for clinker manufacture, including (commonly to a lesser degree) material lost to the system as non-recycled CKD
  8. Dust collectors at plants capture essentially all of the CKD, although this material is not necessarily recycled to the kiln
To use this category, simply create a profile item - there are no drill choices.

Next, specify the quantity of clinker produced using the massClinker profile item value. The quantity returned represents the CO2 emissions associated with the specified production, assuming default values for a number of clinker properties and no production of cement kiln dust.

Overriding default emissions factor

Users can override the default values for clinker calcium oxide (CaO) content and the proportion of this CaO which is sourced from carbonates, which are used to derive the emissions per unit of clinker produced.

The calcining of 1 tonne of limestone (CaCO3) produces 0.5603 tonnes of CaO and 0.4397 tonnes of CO2. It follows that the quantity of CO2 emitted per tonne of CaO produced is 0.7848 tonnes. By specifying the proportion of CaO within the clinker, and the proportion of this CaO which was originally sourced from CaCO3, the CO2 emissions per unit mass of clinker can be derived.

To set the clinker CaO content, specify a decimal fraction (i.e. 0-1) using the clinkerCaOFraction profile item value. If left unspecified, this value defaults to 0.65 following IPCC guidelines. To specify the proportion of CaO derived from carbonate minerals, users can similarly specify a decimal fraction (i.e. 0-1) using the carbonateCaOFraction profile item value. The latter value defaults to 1 - i.e. 100% of CaO is assumed to be sourced directly from carbonates - if left unspecified.

Cement kiln dust

Users can also specify the some information relating to cement kiln dust which was not recycled to the kiln. Such dust represents feedstock 'lost' from the basic calculation, and so the emissions associated with this incompletely calcined dust are accounted for by deriving a correction factor which is applied to the primary emissions factor.

To incorporate the emissions associated with cement kiln dust, set the quantity of cement kiln dust not recycled to the kiln using the massCementKilnDust profile item value. Next, set the fraction calcination of the dust using the cementKilnDustCalcinedFraction profile item value. The calculation assumes that the proportion of original carbonate in the cement kiln dust is the same as in the raw kiln feed.

UIDLabel
9VD43180TOAO clinker production
Calcium oxide fraction in clinker
Fraction of clinker calcium oxide derived from carbonates
Fraction of calcination for cement kiln dust
Quantity of cement kiln dust not recycled to kiln
Quantity of clinker produced